Triton TTS 1400 User Manual download pdf (Page 9)

Ensure that the tool is switched off and the plug is

removed from the power point before making any

adjustments or carrying out maintenance procedures.

Blade maintenance

• Regularly check that the blade is free from a build up

of gum resins or sawdust. If necessary clean with an

appropriate cleaning agent or multi-use lubricant spray

• Regularly check the saw blade for ﬂatness. Use of the

saw with a buckled blade places excessive load on

the motor and gearbox assembly, and may affect your

warranty rights

• Check the tungsten carbide teeth regularly for

sharpness and breakages; re-sharpen or replace

the blade as required. Note that when re-sharpening,

the bevel angles on the front of the teeth should be

retained

Replacing the saw blade

• Only use 165mm / 6-

⁄2" blades, with a kerf between

2.2 & 3.5mm /

⁄32" &

⁄64", designed for circular saws

with a no-load speed rating of at least 5000min

-1

• Never ﬁt high speed steel

blades or abrasive discs.

Fitting of other purpose or

different sized blades will

void the warranty

• Do not ﬁt inferior blades.

Regularly check the blade is

ﬂat, sharp and free of cracks

or defects

1. Rotate the Mode Selection Lever (20)

to Blade Change position

2. Press the Plunge Lock Button (2) and plunge the saw.

The saw will lock at the depth that allows access to

the blade retaining bolt through the panel in the Blade

Housing (22)

3. Fit the Hex Key (21) to the bolt and depress the Spindle

Lock (19)

4. Turn the hex key in the direction of blade rotation (anti-

clockwise) to undo the bolt and remove the bolt and

outer ﬂange

5. Carefully lift the worn blade off the inner washer on the

shaft and slide the blade out through the aperture at

the bottom of the blade housing and set aside

6. Carefully slide the new blade in through the bottom of

the blade housing and position it onto the inner washer

on the shaft. The graphics should face out and the

arrow on the blade should point in the same direction

as the arrow on the housing

7. Reﬁt the outer blade ﬂange then lightly screw the blade

retaining bolt through the outer blade ﬂange

8. Check that the blade is seated properly, depress the

spindle lock and tighten the bolt ﬁrmly with the hex key

9. Depress the plunge lock button to release the plunge

lock and allow the blade to retract fully into the housing

Cleaning

• Keep the tool’s air vents unclogged and clean at all

times

• Remove dust and dirt regularly with a cloth or soft

brush

• Never use caustic agents to clean plastic parts. A damp

cloth is recommended. Water must never come into

contact with the saw

• Re-lubricate all moving parts at regular intervals

Brush replacement

• The carbon brushes are a consumable item which

should be inspected periodically and replaced when

worn

1. With the saw disconnected from power, unscrew the

Brush Access Caps (11). Remove the brushes by pulling

carefully on the protruding springs

2. If either brush is worn to less than 6mm /

⁄64" long,

both brushes must be replaced using genuine Triton

replacement brushes - available from Authorised Triton

Saw Repair Centres

3. Replace/re-ﬁt the brushes, re-ﬁt the brush access caps

and tighten ﬁrmly in place

Note: Triton Precision Power Tools will not be responsible

for any damage or injury caused by mishandling or

unauthorised repair of this tool

MAINTENANCE

Maintenance

950638_Z1MANPRO1_additional AU text.indd 9 27/08/2014 11:31

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 65 66

Comments to this Manuals

No comments

Triton TTS 1400 User Manual Page 9

Comments to this Manuals

Related products and manuals for Tools Triton TTS 1400